TM6111
1Watt ISM band 2.4GHz indoor high power booster
- An indoor 2.4GHz high power booster full pack, including a 1 Watt booster, RF Cable, power adaptor 120-240V, and a installation guide
- Full TDD duplex
- Always in listen mode, and switch to Tx mode while the input power >2dBm to booster
- Switching time is 2ms< preamble timing in IEEE802.11b/g/n
- Good for long distance application in WiFi, Zigbee, etc.
Application & Notes:
- The booster is a bidirectional, with Tx/Rx mode. Always in Listen mode (Rx mode), except Tx requested by system
- Output power is 30dBm at P1dB point
- Input power is 8dBm while its Gain is 22dBm
- A Pei-Attenuator (3 resistors) to adjust the Gain to get best power out
- 1ststep of installation procedure is connecting Antenna to Booster, then turn “power” on to prevent the output RF power reflected destroys the output stage of Booster
LED indicates normal power on and blinking is in Transmitting mode
TM6201
AIOT High Voltage power line monitoring system
An industry network gateway. It links nodes on the high-voltage power line system.
This system includes MCU, battery and battery management system, connection to various networks nodes 2.4GHz wireless radio module, WiFi radio frequency module, connection to 4G LTE based NB-IOT radio module, as well as LAN pots
Regarding the long distance, we need to install WiFi high power booster in the system to extend up to 10kms
The NB-IOT radio module uses the 900/1800MHz frequency, may connect to 4G the LTE base station
This system was installed in the high strength aluminium alloy cabinet, guard against splashes water, the dustproof rank to reach IP-66 level
In the system, you may select and purchase a 30W solar cell, and set a battery management system
18AH battery can provide power continuously with plenty electric current and the voltage
Aluminium alloy cabinet attached the supports, and it may lock the solid instalment on the electricity tower or the related base
2.4GHz 900/1800MHz of antenna have 5dBi gain, and NB-IOT reaches 1 dBi +, which provide good wireless connection
TM6204/5/6
2.4GHz high power RF Transceiver Module with SPI interface
- Size is small in 10x12mm PCBA
- Power output can be up to 20dBm+
- Data rate can be selected based on customer request
- A RF front end IC built in the module to improve propagation performance to extend distance
- Good for 2.4GHz ISM band for wireless gaming, Audio/Video, baby monitoring system, Walky-talky cordless phone and data terminal system
- RF front end IC, Transceiver, crystal and a PXI connector connecting to Antenna
- SPI interface communicate with MCU
- PCB substrate provides GND on bottom side and stamp type Pin pad for easier soldering
- 3 modes 1/2/4 Mbps data rate selection for optimize propagation performance in applications
TM8020
Intelligent Bolt
- Designed for monitoring the important architectures or construction
- Include battery, strain gauge, amplifier, LDO, MCU,DC/RF pins and RF transceiver
- Linkable with Controller or gateway to cloud to accumulate the data for advanced analysis
- 4GHz as the RF communication frequency
- 50Mah power capacity battery provide good support to RF transceiver for transmit status data to controller and it can stand for 3600 secs
- Operation temperature is from -40°C ~ +150°C
- Water proof level XP-6, IPX-7 under 1 meter water for 30 mins
- The system transmits the twisting message of the strain gauge to the controller (TCA) through 2.4GHz wireless transmission
- Control the valve by the controller and control the screw lock
- The CAP has large battery embedded
- When the screw is locked the CAP can monitor the real time torque and clamping force as well as the bolting sequence throughout the bolting procedures
- It can be used in vehicles, buildings, bridges and major equipment